江苏春晨电缆有限公司：https://www.foodjx.com/st161256/

With the application of editing YC cable rubber sheathed cable and submersible pump: it is mainly used for supporting the submersible motor, type JHS, JHSB.

无线电装置用电缆：目前主要生产两种橡套电缆(一种屏蔽的,一种不屏蔽)，基本能满足要求，型号为WYHD，YC。

Cable for radio equipment: at present, the main production of two kinds of rubber sheathed cables (a shield, a shield), the basic can meet the requirements, models for WYHD, YC.

摄影用电缆产品：配合新型光源的发展，具有结构小、性能好，同时满足室内和野外工作的需要，逐步取代一些粗重、耐热性能差的老产品。

Cable product photography: combined with the development of new light source, has the advantages of small structure, good performance, and meet the needs of indoor and field work, gradually replaced the heavy and poor heat resistance of old products.YC橡套电缆

yc橡套电缆分类编辑 橡套电缆分为重型橡套软电缆（YC电缆，YCW电缆），中型橡套软电缆（YZ电缆，YZW电缆），轻型橡套软电缆（YQ电缆，YQW电缆），防水橡套软电缆（JHS电缆，JHSB电缆），电焊机电缆（YH电缆，YHF电缆）YHD电缆为野外用镀锡电源连接线。YC橡套电缆

YC classification edit rubber sheathed cable rubber sheathed cable is divided into heavy cabtyre cable (YC cable, YCW cable), medium soft rubber cable (YZ cable, YZW cable), light soft rubber cable (YQ cable, YQW cable), waterproof rubber sheathed flexible cable (JHS cable, JHSB cable). Electric welding machine cable (YH cable, YHF cable, YHD cable) with tinned power cable field.

yc橡套电缆修补措施编辑 一、设备：具有自动控温、定时和多规格管状模腔的小型压力设备。

YC rubber sheathed cable repair measures, a editing equipment: small pressure equipment with automatic temperature control, timing and sizes of tubular cavity.

二、胶料：与所补电线的线材*，并且含胶量要高于被补材料，硫化体系略强。

Two, rubber material: with the wire of the wire is consistent, and the amount of glue to be higher than the material, curing system is slightly stronger.

三、操作方法：

Three, operation method:

1、按照胶料的硫化体系设定温度和时间

1, according to the curing system of rubber material set temperature and time

2、用橡胶用油墨稀释剂檫洗修补处，特别是结合处要充分处理。

2, with a rubber ink diluent washing repair, especially where the full treatment.

3、根据缺口的大小适量剪取修补胶料，注意不能偏多或偏少，

3, according to the size of the amount of their gap repair adhesive material, not too much or too few,

4、将剪好的胶料塞在缺口处，，注意胶料不要高于电线圆周面。

4, cut a good rubber plug in the gap, and pay attention to the rubber material is not higher than the surface of the wire.

5、用耐高温PP带包好。并将其放入比线径略小的管状模腔里，锁紧上下模，让所补位置具有一定的压力。注意模腔直径比线径略小0.1~0.2mm。

5, with high temperature resistant PP with a package. And put it into the tubular cavity is smaller than the line size in the lock on mode, make up position has a certain pressure. Note the cavity diameter is smaller than the diameter of 0.1~0.2mm.

6、待硫化时间到，取出产品，如有少量胶料溢出，用锋利刀片修尽，并用稀释剂檫尽即可。

6, the curing time to remove the product, if a small amount of glue overflow, with a sharp blade repair, and can make thinner sassafras.

四、验证方法：

Four, verification method:

将适量空气压入所补电线并置于水中，见有无漏气现象即可判定好坏。

The right amount of air into the wire and put it into the water, see whether there is no leakage phenomenon can be judged good or bad.